Found what I needed locally.
Type: Posts; User: miata2fast
Found what I needed locally.
Yes, thank you for pointing that out. I need one from 94-97.
Hello gang!
I am looking for the bracket that holds the fuel pump and sender in the fuel tank. It has the lid on top that attaches to the top of the fuel tank. It doesn't need a working pump,...
Fantastic good time. Got to hang out with some of my old pards, put faces on people I know from forums, and met some new really cool people.
Bought a few parts too!
16780
Anybody happen to have this front bumper side marker connector?
A little brown dog used one of mine as a chew toy.
16776
Had a hell of a time getting the header in. I had to pull the steering shaft out to get the tubes slid in place. Right now I am doing practice runs to see what is the best way to get it in....
I made a big leap in the last few days. The motor is now in the car, which to me is a really big deal. It won't be there for long. I need it in place to mock up everything so when I paint the car,...
Since the motor is mostly complete, it was time to go back and clean up the chassis a bit. Since the car sat for so long, there were a few rust spots that started to develop in areas where I did the...
I get that a lot. Enough so, that I will be doing double duty with the car. Track days on a mild set up, drag race on the wild set up. Its one of the reasons I went with the heavier road race...
It's embarrassing how long it's been since I started on this project, but I am not giving up.
Proof:
16756
Edit: can't figure out why the pic is turned, or how to fix it.
***FTFY :) -...
Remember this old thread?!
I got off track for a couple of years. Had a few things I wanted to do with my life, so I put the car on hold. Bought a flats boat, took ownership of the property...
Years ago I had a set of Steel HKS gears. The only problem I had with them is once they had been run on the car for sometime, they had a tendency to seize together making it difficult to change the...
Last night, I looked at my oil pan, and can now see there is an additional hole for what are obviously the later motor mounts. Thank you for pointing that out to me.
I did a little researching,...
The BP crank scrapper does not sandwich between the oil pan and block. It is attached to the main bearing cap bolts, or in my case studs. No problems with transmission bolt alignment.
I am not...
I know it has been an awfully long time since I posted in this thread, but I have gotten quite a bit done. Some of the things I have been working on are installing both race seats, fabricating seat...
I will buy that to a degree. You can't argue with the fact that rotary motors made cars go fast.
For me, it is a moot point. I would never ever have one. I could not live with the unpleasant...
Those heated intake temps yo!
This has always been what I thought a proper engine swap for a Miata. Shandelle, I would like to have a look see of this project.
There is a member on miataturbo that has done a swap using an MZR...
The room you get from the V8R subframe! It makes life much easier when creating exotic exhaust arrangements.
You can blow into your girlfriends ear or you can suck on her.....well you know. There is nothing gay about it. Honda's on the other hand??
I wish I were there. That VTEC piece of ..... would have his doors sucked off.
You are not supposed to post stuff where we get our @$$ beat. I am afraid I am going to have to take away a thanks given! LoL
How much heavier is the PRHT?
Once I am done with my car, my next project will probably be an NC. I have been wanting one for a while now.
Last night, I spent a little time hammering on the hood, and was pretty discouraged about whether or not I could make it work. I took the hood to the shop this morning and worked on it a little...
I got my hood back yesterday. Not exactly thrilled on how it turned out. The welding warped the sheet metal so bad that it is going to need a lot of metal messaging and body filler to make it...