Aloha MazdaRoadster! Sadly, my red miata got into an accident and the cost to repair the damaged was more than what I expected. My previous shell has been into numerous accidents and has been saved by many DIY fixes (maybe too many DIY fixes.) I decided the best choice was to start over.
A friend of mine donated a shell and it happened to be a 1994 M-Edition. Although this Miata is not in the greatest shape nor is the best choice, it will do for now.
This build thread will be about what I can turn this lemon into and for the thrill of building a Miata.
[New Shell]
So a friend of mine donated this shell under a few agreements.
94 Miata M Edition
Updated: 4/11/2016
Engine:
+99' Head & Block
+ARP Head studs
+ARP Main Studs
+2001+ oiling system
+ACL Race bearing set (Main, Rod, Thrust)
+Fel-Pro Headgasket set
+M-Tuned H-Beamed Forged Connecting Rods
+84mm 9:0.1 Wiseco Pistons
+New 2000 NB crank
+1mm Oversize Valves (Supertech) Exhaust and Intake
+Supertech Valve Springs, Retainers, etc
+Garage Star light weight Water Pump Pulley
+Garage Star light weight Alternator Pulley
+SuperMiata Harmonic Balancer
+Fidanza Adjustable Cam Gears - Silver
+Fab9 Solid Motor Mounts 88D
+NGK Nickle 1-Step colder plugs Gapped at .030 (BKR7E - O'rileys part ref: 4644)
+2000 NB Starter
+323 GTX Turbo PCV
+Protege Valve Cover
+Rotella T6
Intake:
+HellaFababrications Custom "Race" Aluminum Intake Manifold
+Skunk 2 Throttle Body
+2.5" Intercooler piping
+HKS Mushroom/Superflow Air filter
Exhaust
+Custom Equal Length Bottom Mount turbo manifold- Fabricated by HellaFab
+3" Stainless Steel exhaust (V-Banded)- Fabricated by HellaFab
+3" Stainless Steel piping (Cat delete- V-Banded)- Fabricated by HellaFab
+3" Stainless Steel Vibrant Muffler (V-Banded)- Fabricated by HellaFab
+949 Racing Stiff Rubber Exhaust Hangers
Cooling
+Koyo Oversize Radiator
+GarageStar Cooling Panel
+Custom Fan panel (Single fan)
+12" Slim Fan
+Begi Coolant Reroute Spacer w/ fittings
+Water Neck Delete - Freeze plug + Custom Block-off plate
+Coolant re-route (Followed RevLimiter's Write-up) w/ Escalade hoses
+Ebay hose Splicer
+Flipped lower water pump housing
+Setrab Oil Cooler (25 Row) w/ Custom AN lines {kit made by FAB9}
+Mocal Thermostatic Sandwich Plate
+Fab9 Stage 2 Intercooler
+DEI Fire Sleeves
+DEI Gold Heat Insulation tape
Turbo
+IWG = Internal Wastegate
+BorgWarner EFR 6758 (3" exit)
+Turbosmart BOV Fixed 50/50
+Braided Oil feed line (4AN)
+12AN oil drain line
+Water & Oil cooled
Fueling:
+Deatschewerks (sp?) 200 fuel pump
+1000cc Injector Dynamics
+FM Dual Fuel rail
+Pump Gas (92)
Electronics:
+CAS
+Megasquirt PnP v2 engine standalone (94-95)
+Turbosmart Manual Boost Controller
+AEM UEGO wideband
+GM IAT sensor/Speed Density Sensor
+FAB9 Coil On Plug Kit
+Autometer Boost Gauge
+Custom Wire Tuck
+Fuse Block Relocated
Drivetrain
-Resurfaced 1.8 Flywheel
-Miscellanous Short Shifter
-1.8 ACT Clutch kit (ZM2-HDSS)
-94 1.8 Differential (open 4:1)
-94 1.8 Subframe
-94 1.8 Driveshaft
-94 1.8 Axles
-96 1.8 Transmission
Suspension/Stiffening
+ Stance GR+ Coilovers (8k front 6k rear) w/ 15 way dampening levels
+ Custom Extended Rear Top Hats
+ FM Front & Rear Sway Bars
+ Racing Beat Adjustable end links (Rear)
+ Rtheory Motorsports Adjustable end links (Front)
+ Carbing 3pt strut brace
+ OEM hardtop w/ Garage Star top and side security latches
+ Cusco 7pt Roll Cage
+ SuperPro Steering Rack Bushings
+ 94 Depowered Steering Rack - Followed Flyin' Miata's write up
+ GarageStar Steering Rack Spacer
+ MiataRoadster Delete Plugs
+ OE Replacment 94 Miata M-Edition Outer Tie Rod w/ bellow boot kit
Brakes
+NB1 NON-ABS/NON-SPORT Front and Rear brackets w/ Calipers.
+Generic Drilled & Slotted Rotors
+Ceramic C-Tek Brake pads (Will be upgrading to
+949 Racing Braided Brake Lines Front & Rear
+92 Manual Brake Booster
+92 Manual Brake Hard lines
+Custom Heat Shield for Brake Reservoir w/ Gold DEI heat tape
MISC:
+Prosport Sandwich Plate
+Mishimoto Baffle Can (Fab9)
+Golden Eagle vacuum distribution block
+Deleted Air Bag assembly
+Deleted All A/C components
+Deleted heater core & blower
[Specs]
1994
Mazda
Miata
BP-4W (1.9T)
Started putting work..
Started with removing the radiator, harness plugs, vacuum lines, etc...
Motor out! This will be going into my friend's white NA (IG: _trackstance)
How it sits...