Results 1 to 2 of 2

Thread: Maruha BC coilovers

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #1
    6,000 rpm - mere mortals would shift HarryB's Avatar
    Drives
    '04 Strato Blue NB2
    Location
    Greece
    Join Date
    Jun 2015
    Posts
    5,933
    Thanks Given
    6,670
    Thanked 2,273 Times in 1,330 Posts

    Maruha BC coilovers

    As promised, few notes on the Maruha BC coilover set, as seen on their website:

    http://www.maruhamotors.co.jp/parts/bcnb.php

    NOT to be confused with BC Racing!!! Please keep in mind that this is prior to the latest revision; in the latest model, Maruha has increased the rear damper stroke by 20mm, accompanied by OEM-style 20mm extended steel stamped top hats. BTW said extended top hats are perfect for anyone wanting an extremely high quality extended top hat at a reasonable price; anyone building DIY Bilstein coilovers?

    Back to topic; my set was bought used on YAJ and so I took it apart to clean, inspect and measure as much as I could. The version I have comes with 8/6 kg/mm springs (front and rear respectively) and 15-click damping adjustment. There's also a "street" version with lighter spring rates I believe. Both use OEM top hats and OEM rubber bushings, although there's an option for pillow ball ones (which has no real benefit besides reducing side loading on the damper shaft; not much of an issue anyway). Maruha includes machined aluminum adapters to seat the narrower coilover springs and locate them properly in the OEM top hats.

    The design allows you to adjust height separately from spring preload, which has its' benefits (no need for helper springs, can dial in the available bump/rebound travel ratio) but comes to a cost; less stroke than more "conventional" units, as the damper body needs to be physically shorter to accomodate the height adjustment. I believe my units were set per Maruha's reccomendations; rears had a 15mm preload while fronts a 20mm preload. This seemed like much, but it can be attributed to the limited overall stroke and the fact that this leaves you enough bump stroke in expense of rebound.

    Speaking of stroke; rears were measured at 60mm while fronts at 80mm. This is significantly less than OEM NB2 Bilsteins (35mm to be exact), which have a 115/95mm stroke respectively, but can be attributed to the harder springs normally used in coilovers, and (as mentioned) to the inherit design compromise to accomodate separate height adjustment.

    I had contacted Maruha, and bought new OEM rubber "donut" bushings for the top hats, extended top hats (which I will not use on this set up) and new-style bumpstops. The new bumpstops are significantly shorter (20mm total uncompressed length) compared to the older ones (38mm long), but are much stiffer. This means that bumpstops will be engaged much later, but much more abruptly. Will comment back on that once I have some real-world feedback. Just as a reference, the old-style top mounts that originally came with my suspension had turned to dust on the rears (1-2mm of residue was all that was left), indicating frequent bottoming out. This is something that worries me; it should be OK with the original springs, but I was planning to go down to 6/4.5 kg/mm, as I do my fair bit of mountain passes drives, and potholes are frequent. However, this means more travel is needed for the same load; thus more frequent bumpstop contact. Seems I will be sticking to the original supplied springs for now.

    Few words on overall build quality; as anything from Maruha, quality is top-tier. Clean threads, and despite the dirt everything came apart with ease. Coating was intact in all parts including springs. Something I would love would be plastic/rubber spring seats, but I do not see it being a problem, separate preload adjustment means no loose springs to rattle around. Another important observation is that although Maruha advises in replacing the damper units once shot, these are proper rebuildable ones. The bottom cap is removable (threaded not crimped) and there's a schrader valve installed on the bottom, although not visible with the units assembled. Pic of said stuff:



    I can see their reasoning (they would ask people to ship back to them, labor cost is high and Maruha is a relatively small business, therefore turnover time would be long and most probably was going to cost more to service than replace), however I would like to try and see what's possible when time comes. Moreover, as per Maruha, these use 46mm pistons; same as Bilstein, and Bilstein parts (including pistons, seals, shim stacks etc.) can be purchased individually.

    Glory picture after cleaning everything up

    Last edited by HarryB; 01-03-2019 at 03:10 PM.

  2. The Following 7 Users Say Thank You to HarryB For This Useful Post:

    91BRG (01-02-2019),Greasemonkey2000 (01-02-2019),MaRcOp01o (01-02-2019),MX5Wisher (01-03-2019),oldgrayleather (01-02-2019),Slampen (01-03-2019),vindi49 (01-02-2019)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •