Results 61 to 68 of 68
Thread: Miata Headers, all of them, which one do you own?
LIKE THIS THREAD!
-
06-13-2016, 05:40 PM #61
- Drives
- blue, white and two-tone
- Location
- South London, UK
- Join Date
- May 2016
- Posts
- 139
- Thanks Given
- 53
- Thanked 90 Times in 36 Posts
I have this - an RS*R 4-1 manifold:
This is what they look like unwrapped:
-
The Following 3 Users Say Thank You to atlex For This Useful Post:
Demon I Am (06-13-2016),Fishbulb (06-14-2016),NCGreasemonkey (06-14-2016)
-
06-14-2016, 12:30 AM #62
- Drives
- '95 NA NA8 w/small tweeks
- Location
- Winston-Salem, N.C.
- Join Date
- Oct 2015
- Posts
- 4,425
- Thanks Given
- 3,896
- Thanked 1,449 Times in 859 Posts
Wow. So the Air/fuel sensor (or O2) is just monitoring cylinder 4? That might be scary! And it is closer than 18" from the port. That scares me more. Just wondering how that is working for you?
-
The Following User Says Thank You to NCGreasemonkey For This Useful Post:
HarryB (06-01-2017)
-
06-14-2016, 04:05 AM #63
- Drives
- blue, white and two-tone
- Location
- South London, UK
- Join Date
- May 2016
- Posts
- 139
- Thanks Given
- 53
- Thanked 90 Times in 36 Posts
it's fine and not all that uncommon. I have a turbo'd car with the same setup - meter reads off port 4.
-
08-08-2016, 10:45 PM #64
- Drives
- Eunos Roadster
- Join Date
- May 2016
- Posts
- 20
- Thanks Given
- 2
- Thanked 8 Times in 4 Posts
I'm a musician (multi instrumentalist) for 30 years so sound is most important to me VS a 2 hp gain or a shiny thing under my bonnet
Currently I have a Fujitsubo in my 1.8 that came with the car.
I dislike it as it sounds too subtle and flat. It goes through stock cat to Borla muffler ... Very unexciting at idle and at high rev , sound wise I would call this "The Bland Combo" even stock car sound better at high revs also , I know the Borla has a lot to do with it too but someone else said the Fujitsubo is low pitched in a previous post here.
My last setup screamed like a race car , high pitched & very throaty.
Was an Apexi "spiral " to a Car Make Corn's muffler... Will install after car passes inspection this week.Last edited by EunosMonster; 08-08-2016 at 11:26 PM.
-
08-09-2016, 03:18 AM #65
-
11-16-2018, 02:24 PM #66
- Drives
- 1995 Merlot Mica
- Location
- Miami Beach, Fl.
- Join Date
- Dec 2011
- Posts
- 1,461
- Thanks Given
- 989
- Thanked 282 Times in 203 Posts
Can someone ID if this is a NA8 vs NA6 header?
The flange for the catalytic converters has been cut off.
-
11-16-2018, 02:25 PM #67
- Drives
- 1995 Merlot Mica
- Location
- Miami Beach, Fl.
- Join Date
- Dec 2011
- Posts
- 1,461
- Thanks Given
- 989
- Thanked 282 Times in 203 Posts
-
11-16-2018, 04:22 PM #68
- Drives
- Fast as I can
- Join Date
- Jul 2017
- Posts
- 755
- Thanks Given
- 813
- Thanked 95 Times in 70 Posts
Looks to be a 1.8. Only using my Google-Fu looking at the front left flange. I think. Don't trust me though
-
The Following User Says Thank You to MX5Wisher For This Useful Post:
etikoner (11-22-2018)
MazdaSpeed Time Trap/Trap Timer
02-06-2019, 08:21 AM in WANTED