Ok, no worries. Had buyers lined up already after your right to decline. The Ryoku Rob hooks are sold!
The Garage Star ones are still available.
Type: Posts; User: CMP
Ok, no worries. Had buyers lined up already after your right to decline. The Ryoku Rob hooks are sold!
The Garage Star ones are still available.
Bumping this because it so happens that I have a pair of Ryoku Rob v2 NA hooks and a pair of Garage Star hooks available.
21716
21717
I have a driver's side seat bracket sitting idle on a shelf in my garage. It has been mounted previously and the mounting holes were gauged out for adjustment. I know it's not a pair but it gets...
What size? 15"? I make a center cap for these but it's not flat.
I don't think you can use flat caps in the rear because the axle stud may protrude too far. If you check on that, I might be...
I notice you have one for both NA and NB... which should one order when one has an NA with NB subframes? Does it matter?
Yes please! I know that the 14" variant has a stepped hub bore, and the rear of the hub bore sits flush, which prevents use of a standard center cap design like that used on the 15" RPF1. There is...
I drive right through RDU to visit my folks in VA, maybe we can work something out. Might be easier just to ship you lo-res testing models.
They will be available, given time, though I'm not sure if they'll go full production like the 15" version due to costs and demand. It's not hard to DIY the 3d printed versions, just time-consuming....
Here are the very first potatocam pics of the pre-production center caps with Adam's lovely work attached to them.
https://c2.staticflickr.com/6/5786/29313036793_2b95d3cd53_b.jpg
...
I received the first set of pre-production center caps last weekend and started painting them. Since they're 3d printed, the surface is rough, unlike injection molded plastic, so they're taking a...
Technically speaking, these aren't for my Miata, since I ordered the center cap decals for my Mazda 2, but Adam took good care of me and I wanted to share it with you guys. These will soon be...
Your first order is on the way!
Thanks, but you should probably take that up with Marc. All I did was design a center cap; I don't represent CarbonMiata.
This cap was an initial lo-res test run and has been altered in design since. The furthest protruding axle stub I found thus far was on the rear of a Miata, and the finished design clears it just...
Marc is handling that aspect of it. I'm just the designer and have no experience in such things. :)
The product is finished and has been sent to Marc at CarbonMiata for production. I discovered that these should also work on the Konig Helium so that broadens our market.
...
We have Shapeways here in the US for this, and I'm using them to 3D print my Enkei RPF1 center cap test designs.
Check this guy out.
I just wanted to pop in and mention that I'm finalizing the design for the 15" RPF1 center caps, and will be teaming up with Marc over at CarbonMiata to produce them very soon.
14" versions will...
I was quoted $2k for the price on their facebook page, plus shipping. They're close so I'd just drive down to get it.
"Fastback is $2000 plus shipping. That includes the roof, decklid, Lexan...
Thank you sir.
This is my recommendation as well. I used this for my Project G corner flares and it matched up perfectly.
I think 14" and 15" are the same. Please measure your hub bore diameter for me and PM me the info so I can compare to the 15" dimensions.
I am actually in the process of designing center caps that fit 15" RPF1s. I intend to leave a 58mm blank area on the exterior so end users may add their own custom badging - in this case, Adam's...
This is a tough question for me... I came into it with a fairly hefty amount of experience wrenching on Hondas, so I was at full tilt from the moment I bought the Miata. I started in the first...
Could be worse. At least it doesn't have "Forest Whitaker Eye".
16082