Page 19 of 19 FirstFirst ... 91213141516171819
Results 271 to 277 of 277

Thread: The 'I told you, you'd be back' build of Misfire, my NB2 w/ F1 inspiration

  1. #271
    5,000 rpm - there be torque here! Greasemonkey2000's Avatar
    Drives
    2001 NB2 aka Misfire
    Location
    Temple, Tx is where Chad resides.
    Join Date
    Nov 2013
    Posts
    3,776
    Thanks Given
    4,790
    Thanked 2,315 Times in 1,182 Posts
    03-21-21, Mileage- 126,616: I am ashamed to say that it has been almost two years since I changed Misfire's oil(04/20/19 @119,205 miles) but only about 7400 miles. Okay, either way I know I should do it at least once a year which I am going to start doing...I promise.

    Picked up two more Purolator Boss PBL14610 filters a few months ago and decided to try Castrol GTX Magnatec 5w30 this time around. It is suppose to "stick to metal parts" to give better protection on start up.


    I had also picked up one of Fumoto's new F106SX valves(the bolt is a banjo type and the valve can swivel to set the direction) but after seeing it hung down approx. 0.25" below the oil pan and sub frame, I opted not to install it given I plan to lower Misfire another inch or so.

    The filter was a bit of a pan to get off. I was actually trying to see if one of my friends had a oil filter wrench that would fit but no one had one small enough. After much exertion, it finally came off.

    Everything else went as expected but I have a small oil leak some where at the front of the motor which I honestly didn't take the time to track down.

    I had also replaced the CV boot that I was using as a shift boot for a Audi MKI TT shift boot a few weeks ago but forgot to post a picture.




    I'm not sure if I will install the whole Audi TT shift console after all...in fact I think I am going to do a center console delete. I recently found a great option for the tombstone end cap for NB's from Jass Performance.

    https://www.jassperformance.com/shop...-Tombstone-Cap

    That is probably the route I will go with.
    Last edited by Greasemonkey2000; 03-21-2021 at 11:11 PM.
    '01 NB2 aka MisF1re: http://mazdaroadster.net/showthread....218#post207218
    '97 M aka Warbird, gone but not forgotten: http://mazdaroadster.net/showthread....B&goto=newpost
    Instagram: @greasemonkey2000

  2. The Following 3 Users Say Thank You to Greasemonkey2000 For This Useful Post:

    Bryan (03-22-2021),Cermivelli (03-22-2021),lifebyevan (03-22-2021)

  3. #272
    1,000 rpm - releasing the clutch lifebyevan's Avatar
    Drives
    Mahogony Mica '00 Special Edition NB1
    Location
    Orlando, FL
    Join Date
    Feb 2020
    Posts
    77
    Thanks Given
    28
    Thanked 93 Times in 28 Posts
    Fresh oil change just in time for the spring festivities Hooray for Misfire!

    I think the tombstone end cap would fit the look for Misfire. It's nice they give you the switches for the window switches built-in.

  4. #273
    Super Moderator Bryan's Avatar
    Drives
    '02 Laser Blue Mica
    Location
    Cincinnati, OH
    Join Date
    Dec 2011
    Posts
    5,181
    Thanks Given
    757
    Thanked 1,728 Times in 913 Posts
    The Tick needs an oil change. It spent a year with 15w40 (Rotella T4 instead of the T6) in the oil pan.
    Quote Originally Posted by DazedAndConfused
    I dont know a word you just said, but that **** sounded COOL.

  5. #274
    5,000 rpm - there be torque here! Greasemonkey2000's Avatar
    Drives
    2001 NB2 aka Misfire
    Location
    Temple, Tx is where Chad resides.
    Join Date
    Nov 2013
    Posts
    3,776
    Thanks Given
    4,790
    Thanked 2,315 Times in 1,182 Posts
    03-22-21: Finally got around to refinishing Misfire's headlights, again, as I didn't do any kind of permanent seal coat or finish when I refinished them two years ago.

    I was going to do the whole process over and then use a ceramic coat but after using the ceramic coat on the side markers and not being too sure about the results I decided to use actual clear coat.

    Since I don't have a compressor and paint gun, I went with a aerosol clear coat. Having already research options, it seemed the general consensus was that 2k clear coat was the best option which has the clear coat plus a hardener that you release by using a "button" that is included.

    I wet sanded with 800 grit and then 1200, iirc, cleaned thoroughly, wiped down with rubbing alcohol and after masking the hood, fenders and bumper off, I applied the 2k clear coat(SprayMax 3680061, which I don't recommend) in a few light coats(2) and then two medium coats. Letting the clear coat dry for about 10 minutes between coats and used a heat gun to try and speed it up.

    Right away there was obvious orange peel so I knew that I would have to wet sand, compound and polish which I did after letting the clear coat setup for about 12hrs.

    The results are pretty good but I may have needed to go to 600 grit because the passenger side still has obvious yellowing which isn't as apparent in pictures but still discernible when comparing to the driver side.

    Driver side(before)


    Drive side(after)


    Passenger side(before)


    Passenger side(after)



    I plan on picking up another set of NB2 headlights to refinish, paint the inner housing black, add a switchback halo on the low beam and possibly upgrade the high beam to a projector lens.
    '01 NB2 aka MisF1re: http://mazdaroadster.net/showthread....218#post207218
    '97 M aka Warbird, gone but not forgotten: http://mazdaroadster.net/showthread....B&goto=newpost
    Instagram: @greasemonkey2000

  6. The Following 2 Users Say Thank You to Greasemonkey2000 For This Useful Post:

    Demon I Am (03-30-2021),HarryB (03-30-2021)

  7. #275
    5,000 rpm - there be torque here! Greasemonkey2000's Avatar
    Drives
    2001 NB2 aka Misfire
    Location
    Temple, Tx is where Chad resides.
    Join Date
    Nov 2013
    Posts
    3,776
    Thanks Given
    4,790
    Thanked 2,315 Times in 1,182 Posts
    03-29-21: Picked up a set of Katana LED 9005 bulbs(about $50 shipped on Amazon) to replace Misfire's halogen bulbs(I believe they are Sylvania Silverstar Ultra).




    When unpacking the bulbs I recalled I never did check on the correct orientation of LED bulbs when they replace halogens, something I meant to do when I bought the Katana LED bulbs for the low beams.

    One quick internet search later and I found that the LED's should be facing 3 and 9 in the headlight when replacing a halogen bulb, in a fixture meant for halogen bulbs.

    I checked the low beams and sure enough they were both turned 90 degrees, facing 12 and 6. I decided to just fix(just loosen a allen head set screw on the mounting collar, move and tighten set screw) the driver side to see the difference which was pretty obvious.

    Driver side with low beam LED bulb correctly oriented at 3 and 9 and passenger side incorrectly oriented at 12 and 6:




    Both low beam LED bulbs oriented correctly at 3 and 9:


    As you can see with the passenger side incorrectly oriented at 12 and 6, there is more overlap of the beams causing a large hot spot in the center and it throwing further instead of wider.

    Katana LED bulbs for low beam and Sylvania Silverstar Ultra(i believe) halogen bulbs for high beam:


    Katana LED bulbs for low and high beam:


    I'm very pleased with the results, considering these are $50 LED bulbs, so essentially "cheap" LED bulbs and the ones I bought a year ago have held up thus far with no issues. $50 is what you would pay for "premium" halogen bulbs so I would take these over the "premium" halogen bulbs any day of the week.
    '01 NB2 aka MisF1re: http://mazdaroadster.net/showthread....218#post207218
    '97 M aka Warbird, gone but not forgotten: http://mazdaroadster.net/showthread....B&goto=newpost
    Instagram: @greasemonkey2000

  8. The Following 4 Users Say Thank You to Greasemonkey2000 For This Useful Post:

    Bryan (03-30-2021),Demon I Am (03-30-2021),HarryB (03-30-2021),MiataQuest (03-30-2021)

  9. #276
    4,000 rpm - entering the fun zone RustRat's Avatar
    Drives
    Red NA8C 1.6L
    Location
    Mediterranean Sea
    Join Date
    Sep 2014
    Posts
    1,221
    Thanks Given
    1,578
    Thanked 935 Times in 462 Posts
    A lot going on here, need to get reading. Your builds are always interesting, and it pleases me to see you still wrenching


    Sent from my iPhone using Tapatalk

  10. #277
    5,000 rpm - there be torque here! MaRcOp01o's Avatar
    Drives
    1991 BRG, 1993 EUNOS, 2018 HONDA FIT
    Location
    Miami,Fl
    Join Date
    Jul 2017
    Posts
    2,287
    Thanks Given
    1,250
    Thanked 1,235 Times in 503 Posts
    I think you officially have the brightest roadster on the forum.

  11. The Following User Says Thank You to MaRcOp01o For This Useful Post:

    HarryB (03-31-2021)

Page 19 of 19 FirstFirst ... 91213141516171819

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •