That looks great! Seems they still leave a bit of the leading edge of the tire exposed, but seeing that they're S2K canards that's understandable.
That looks great! Seems they still leave a bit of the leading edge of the tire exposed, but seeing that they're S2K canards that's understandable.
I've got a lot less horsepower - luckily they are Japanese horses - usually in better shape and more motivated.
looking good
atxsbigwalt (02-08-2015),Ihatecars (02-11-2015),RotorNutFD3S (02-09-2015),speedypenguin (02-09-2015)
Car is perfect. Anything you do will just be icing on the cake. That's just me being naive. I hate to see an excellent built go to disaster. IMHO all the weak links have been address from what I see.
i love it; that isnt OEM paint is it?? looks in great shape
Instragram, will follow back. @JDMFreshnessTX
https://www.facebook.com/JDMfreshness
http://www.jdmfreshness.com/
So nice, so gangster :drool:
The front canards look kind of off, I love those rear add ons from GV, get them fitted!
Thanks.
Its OEM paint! Well most of it since I've replace alot of body parts. I started using this water less cleaner on my car. I love it so far!
Yeah, your probably right about the canards. I can remove them without leaving any damage on my front bumper if I get tired of them.
Hope you keep this for a very long time. It'd be interesting to have two Jetstream cars running Houston when I get to that point, especially since our cars are actually going to be quite a bit different looking.
I personally believe the car will look a lot better with a flat trunk lid and without the hard top spoiler. I do like the front bumper side skirts and everything else tough, just not a fan of spoilers. that's all
I just read the whole thing.
You make art.
pacman 99 (03-13-2015)
Finally installed my GV rear garnish pieces. Overall fitment was spot on.
I got my replacement I.L Motorsports hood lift kit last week. My original ones couldn't hold the hood up anymore. Looks they upgraded it with better hardware pieces.
Old on the left and new on the right.
I also bought a Renown 100 Dark steering wheel. I've always wanted a deep dish black on black steering wheel. Never found any that would fit this criteria. Renown announced this suede steering wheel a few months ago and I pre-ordered it. Finally arrived this week and I'm pretty happy with it.
Comes in a plain black box.
Steering wheel is 350mm in diameter and has a 100 offset. Comes with a horn and hardware!
I have a slim Works Bell hub(55mm) with Nardi adapter. The Nardi adapter shown here had to be removed since Renown uses the Momo bolt pattern. Plus I don't need the extra 12mm this adapter creates since the Renown steering wheel is deeper than my Nardi. Nardi 80mm dish compare to Renown's 100mm.
Removed.
Next I had to relocate the airbag connector to the outside of the hub. I had it inside the hub since the Nardi adapter created extra space for the Nardi horn.
Renown horn button uses two contacts to power the horn. Ground and power. Renown includes a ground wire for the horn installation. I ended up using the hole on the steering rod as my ground source since it was already threaded for a M5 bolt. The M5 bolt is not included with the steering wheel.
All ready for the wheel to be installed.
Quality is great. It does feel a bit heavier than the Nardi. I should of weighed the difference but I was too excited and forgot.
The grip on the steering wheel feels a bit thicker as well since it doesn't have those grooves on the backside for your fingers like Nardi's.
I can still reach the stalks without completely removing my hand from the steering wheel. Just barely.
Some more exterior shots with the new GV part.
Last edited by pacman 99; 03-20-2015 at 06:34 PM.
top notch again sir
Instragram, will follow back. @JDMFreshnessTX
https://www.facebook.com/JDMfreshness
http://www.jdmfreshness.com/
pacman 99 (03-20-2015)
RotorNutFD3S (03-22-2015),Tkblazer (03-21-2015)